Effective medium approximations
In materials science, effective medium approximations (EMA) or effective medium theory (EMT) pertain to analytical or theoretical modeling that describes the macroscopic properties of composite materials. EMAs or EMTs are developed from averaging the multiple values of the constituents that directly make up the composite material. At the constituent level, the values of the materials vary and are inhomogeneous. Precise calculation of the many constituent values is nearly impossible. However, theories have been developed that can produce acceptable approximations which in turn describe useful parameters including the effective permittivity and permeability of the materials as a whole. In this sense, effective medium approximations are descriptions of a medium (composite material) based on the properties and the relative fractions of its components and are derived from calculations,[1][2] and effective medium theory.[3] There are two widely used formulae.[4]
Effective permittivity and permeability are averaged dielectric and magnetic characteristics of a microinhomogeneous medium. They both were derived in quasi-static approximation when the electric field inside a mixture particle may be considered as homogeneous. So, these formulae can not describe the particle size effect. Many attempts were undertaken to improve these formulae.
Applications
There are many different effective medium approximations,[5] each of them being more or less accurate in distinct conditions. Nevertheless, they all assume that the macroscopic system is homogeneous and, typical of all mean field theories, they fail to predict the properties of a multiphase medium close to the percolation threshold due to the absence of long-range correlations or critical fluctuations in the theory.
The properties under consideration are usually the conductivity or the dielectric constant of the medium. These parameters are interchangeable in the formulas in a whole range of models due to the wide applicability of the Laplace equation. The problems that fall outside of this class are mainly in the field of elasticity and hydrodynamics, due to the higher order tensorial character of the effective medium constants.
EMAs can be discrete models, such as applied to resistor networks, or continuum theories as applied to elasticity or viscosity. However, most of the current theories have difficulty in describing percolating systems. Indeed, among the numerous effective medium approximations, only Bruggeman's symmetrical theory is able to predict a threshold. This characteristic feature of the latter theory puts it in the same category as other mean field theories of critical phenomena.[citation needed]
Bruggeman's model
For a mixture of two materials with permittivities and with corresponding volume fractions and , D.A.G. Bruggeman proposed a formula of the following form:[6]
with (3)
Here positive sign before the square root must be altered to negative sign in some cases in order to get correct imaginary part of effective complex permittivity which is related with electromagnetic wave attenuation. The formula is symmetric with respect to swapping the 'd' and 'm' roles. This formula is based on the equality
(4)
where is the jump of electric displacement flux all over the integration surface, is the component of microscopic electric field normal to the integration surface, is the local relative complex permittivity which takes the value inside the picked metal particle, the value inside the picked dielectric particle and the value outside the picked particle, is the normal component of the macroscopic electric field. Formula (4) comes out of Maxwell's equality . Thus only one picked particle is considered in Bruggeman's approach. The interaction with all the other particles is taken into account only in mean field approximation described by . Formula (3) gives a reasonable resonant curve for plasmon excitations in metal nanoparticles if their size is 10 nm or smaller. But it is unable to describe the size dependence for the resonant frequency of plasmon excitations that are observed in experiment [7]
Formulas
Without any loss of generality, we shall consider the study of the effective conductivity (which can be either dc or ac) for a system made up of spherical multicomponent inclusions with different arbitrary conductivities. Then the Bruggeman formula takes the form:
Circular and spherical inclusions
In a system of Euclidean spatial dimension that has an arbitrary number of components,[8] the sum is made over all the constituents. and are respectively the fraction and the conductivity of each component, and is the effective conductivity of the medium. (The sum over the 's is unity.)
Elliptical and ellipsoidal inclusions
This is a generalization of Eq. (1) to a biphasic system with ellipsoidal inclusions of conductivity into a matrix of conductivity .[9] The fraction of inclusions is and the system is dimensional. For randomly oriented inclusions,
where the 's denote the appropriate doublet/triplet of depolarization factors which is governed by the ratios between the axis of the ellipse/ellipsoid. For example: in the case of a circle {, } and in the case of a sphere {, , }. (The sum over the 's is unity.)
The most general case to which the Bruggeman approach has been applied involves bianisotropic ellipsoidal inclusions.[10]
Derivation
The figure illustrates a two-component medium.[8] Consider the cross-hatched volume of conductivity , take it as a sphere of volume and assume it is embedded in a uniform medium with an effective conductivity . If the electric field far from the inclusion is then elementary considerations lead to a dipole moment associated with the volume
This polarization produces a deviation from . If the average deviation is to vanish, the total polarization summed over the two types of inclusion must vanish. Thus
where and are respectively the volume fraction of material 1 and 2. This can be easily extended to a system of dimension that has an arbitrary number of components. All cases can be combined to yield Eq. (1).
Eq. (1) can also be obtained by requiring the deviation in current to vanish [11] [12] . It has been derived here from the assumption that the inclusions are spherical and it can be modified for shapes with other depolarization factors; leading to Eq. (2).
A more general derivation applicable to bianisotropic materials is also available.[10]
Modeling of percolating systems
The main approximation is that all the domains are located in an equivalent mean field. Unfortunately, it is not the case close to the percolation threshold where the system is governed by the largest cluster of conductors, which is a fractal, and long-range correlations that are totally absent from Bruggeman's simple formula. The threshold values are in general not correctly predicted. It is 33% in the EMA, in three dimensions, far from the 16% expected from percolation theory and observed in experiments. However, in two dimensions, the EMA gives a threshold of 50% and has been proven to model percolation relatively well.[13] [14][15]
Maxwell Garnett equation
In the Maxwell Garnett approximation,[16] the effective medium consists of a matrix medium with and inclusions with . Maxwell Garnett was the son of physicist William Garnett, and was named after Garnett's friend, James Clerk Maxwell. He proposed his formula to explain colored pictures that are observed in glasses doped with metal nanoparticles. His formula has a form
(1)
where is effective relative complex permittivity of the mixture, is relative complex permittivity of the background medium containing small spherical inclusions of relative permittivity with volume fraction of . This formula is based on the equality
(2)
where is the absolute permittivity of free space and is electric dipole moment of a single inclusion induced by the external electric field E. However this equality is good only for homogeneous medium and . Moreover the formula (1) ignores the interaction between single inclusions. Because of these circumstances, formula (1) gives too narrow and too high resonant curve for plasmon excitations in metal nanoparticles of the mixture.[17]
Formula
The Maxwell Garnett equation reads:[18]
where is the effective dielectric constant of the medium, of the inclusions, and of the matrix; is the volume fraction of the inclusions.
The Maxwell Garnett equation is solved by:
so long as the denominator does not vanish. A simple MATLAB calculator using this formula is as follows.
% This simple MATLAB calculator computes the effective dielectric
% constant of a mixture of an inclusion material in a base medium
% according to the Maxwell Garnett theory as introduced in:
% https://en.wikipedia.org/wiki/Effective_Medium_Approximations
% INPUTS:
% eps_base: dielectric constant of base material;
% eps_incl: dielectric constant of inclusion material;
% vol_incl: volume portion of inclusion material;
% OUTPUT:
% eps_mean: effective dielectric constant of the mixture.
function [eps_mean] = MaxwellGarnettFormula(eps_base, eps_incl, vol_incl)
small_number_cutoff = 1e - 6;
if vol_incl < 0 || vol_incl > 1
disp(['WARNING: volume portion of inclusion material is out of range!']);
end
factor_up = 2 * (1 - vol_incl) * eps_base + (1 + 2 * vol_incl) * eps_incl;
factor_down = (2 + vol_incl) * eps_base + (1 - vol_incl) * eps_incl;
if abs(factor_down) < small_number_cutoff
disp(['WARNING: the effective medium is singular!']);
eps_mean = 0;
else
eps_mean = eps_base * factor_up / factor_down;
end
end
Derivation
For the derivation of the Maxwell Garnett equation we start with an array of polarizable particles. By using the Lorentz local field concept, we obtain the Clausius-Mossotti relation:
Where is the number of particles per unit volume. By using elementary electrostatics, we get for a spherical inclusion with dielectric constant and a radius a polarisability :
If we combine with the Clausius Mosotti equation, we get:
Where is the effective dielectric constant of the medium, of the inclusions; is the volume fraction of the inclusions.
As the model of Maxwell Garnett is a composition of a matrix medium with inclusions we enhance the equation:
Validity
In general terms, the Maxwell Garnett EMA is expected to be valid at low volume fractions , since it is assumed that the domains are spatially separated and electrostatic interaction between the chosen inclusions and all other neighbouring inclusions is neglected.[21] The Maxwell Garnett formula, in contrast to Bruggeman formula, ceases to be correct when the inclusions become resonant. In the case of plasmon resonance, the Maxwell Garnett formula is correct only at volume fraction of the inclusions .[22] The applicability of effective medium approximation for dielectric multilayers [23] and metal-dielectric multilayers [24] have been studied, showing that there are certain cases where the effective medium approximation does not hold and one needs to be cautious in application of the theory.
Formula describing size effect
A new formula describing size effect was proposed.[17] This formula has a form
(5)
,
where a is the nanoparticle radius and is wave number. It is supposed here that the time dependence of the electromagnetic field is given by the factor In this paper Bruggeman's approach was used, but electromagnetic field for electric-dipole oscillation mode inside the picked particle was computed without applying quasi-static approximation. Thus the function is due to the field nonuniformity inside the picked particle. In quasi-static region , i.e. ≤ 10 nm for Ag this function becomes constant and formula (5) becomes identical with Bruggeman's formula.
Effective permeability formula
Formula for effective permeability of mixtures has a form [17]
(6)
Here is effective relative complex permeability of the mixture, is relative complex permeability of the background medium containing small spherical inclusions of relative permeability with volume fraction of . This formula was derived in dipole approximation. Magnetic octupole mode and all other magnetic oscillation modes of odd orders were neglected here. When and this formula has a simple form [17]
(7)
Effective medium theory for resistor networks
For a network consisting of a high density of random resistors, an exact solution for each individual element may be impractical or impossible. In such case, a random resistor network can be considered as a two-dimensional graph and the effective resistance can be modelled in terms of graph measures and geometrical properties of networks.[25] Assuming, edge length electrode spacing and edges to be uniformly distributed, the potential can be considered to drop uniformly from one electrode to another. Sheet resistance of such a random network () can be written in terms of edge (wire) density (), resistivity (), width () and thickness () of edges (wires) as:
See also
References
- ^ Wenshan, Cai; Shalaev, Vladimir (November 2009). Optical Metamaterials: Fundamentals and Applications. Springer. pp. Chapter 2.4. ISBN 978-1-4419-1150-6.
- ^ Wang, M; Pan, N (2008). "Predictions of effective physical properties of complex multiphase materials" (Free PDF download). Materials Science and Engineering: R: Reports. 63: 1–30. doi:10.1016/j.mser.2008.07.001.
- ^ T.C. Choy, "Effective Medium Theory", Oxford University Press, (2016) 241 p.
- ^ M. Scheller, C. Jansen, M. Koch, "Applications of Effective Medium Theories in the Terahertz Regime" in Recent Optical and Photonic Technologies, ed. by K.Y. Kim, Intech, Croatia, Vukovar (2010), p. 231.
- ^ Tinga, W. R.; Voss, W. A. G.; Blossey, D. F. (1973). "Generalized approach to multiphase dielectric mixture theory". J. Appl. Phys. 44 (9): 3897. Bibcode:1973JAP....44.3897T. doi:10.1063/1.1662868. Archived from the original on 2012-07-16. Retrieved 2019-04-24.
- ^ Bruggeman, D. A. G. (1935). "Berechnung verschiedener physikalischer Konstanten von heterogenen Substanzen. I. Dielektrizitätskonstanten und Leitfähigkeiten der Mischkörper aus isotropen Substanzen". Annalen der Physik. 416 (7): 636–664. Bibcode:1935AnP...416..636B. doi:10.1002/andp.19354160705. ISSN 0003-3804.
- ^ S.J. Oldenburg. "Silver Nanoparticles: Properties and Applications". Sigma Aldrich. Retrieved 17 May 2019.
- ^ a b Landauer, Rolf (April 1978). "Electrical conductivity in inhomogeneous media". AIP Conference Proceedings. Vol. 40. American Institute of Physics. pp. 2–45. doi:10.1063/1.31150. Archived from the original on 2012-07-10. Retrieved 2010-02-07.
- ^ Granqvist, C. G.; Hunderi, O. (1978). "Conductivity of inhomogeneous materials: Effective-medium theory with dipole-dipole interaction". Phys. Rev. B. 18 (4): 1554–1561. Bibcode:1978PhRvB..18.1554G. doi:10.1103/PhysRevB.18.1554.
- ^ a b Weiglhofer, W. S.; Lakhtakia, A.; Michel, B. (1998). "Maxwell Garnett and Bruggeman formalisms for a particulate composite with bianisotropic host medium". Microw. Opt. Technol. Lett. 15 (4): 263–266. doi:10.1002/(SICI)1098-2760(199707)15:4<263::AID-MOP19>3.0.CO;2-8. Archived from the original on 2013-01-05.
- ^ Stroud, D. (1975). "Generalized effective-medium approach to the conductivity of an inhomogeneous material". Phys. Rev. B. 12 (8): 3368–3373. Bibcode:1975PhRvB..12.3368S. doi:10.1103/PhysRevB.12.3368.
- ^ Davidson, A.; Tinkham, M. (1976). "Phenomenological equations for the electrical conductivity of microscopically inhomogeneous materials". Phys. Rev. B. 13 (8): 3261–3267. Bibcode:1976PhRvB..13.3261D. doi:10.1103/PhysRevB.13.3261.
- ^ Kirkpatrick, Scott (1973). "Percolation and conduction". Rev. Mod. Phys. 45 (4): 574–588. Bibcode:1973RvMP...45..574K. doi:10.1103/RevModPhys.45.574.
- ^ Zallen, Richard (1998). The Physics of Amorphous Solids. Wiley-Interscience. ISBN 978-0-471-29941-7.
- ^ Rozen, John; Lopez, René; Haglund, Richard F. Jr.; Feldman, Leonard C. (2006). "Two-dimensional current percolation in nanocrystalline vanadium dioxide films". Appl. Phys. Lett. 88 (8): 081902. Bibcode:2006ApPhL..88h1902R. doi:10.1063/1.2175490. Archived from the original on 2012-07-12. Retrieved 2019-04-24.
- ^ Garnett, J. C. M. (1904). "Colours in Metal Glasses and in Metallic Films". Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences. 203 (359–371): 385–420. Bibcode:1904RSPTA.203..385G. doi:10.1098/rsta.1904.0024. ISSN 1364-503X.
- ^ a b c d Belyaev, B. A.; Tyurnev, V. V. (2018). "Electrodynamic Calculation of Effective Electromagnetic Parameters of a Dielectric Medium with Metallic Nanoparticles of a Given Size". Journal of Experimental and Theoretical Physics. 127 (4): 608–619. Bibcode:2018JETP..127..608B. doi:10.1134/S1063776118100114. ISSN 1063-7761. S2CID 125250487.
- ^ Choy, Tuck C. (1999). Effective Medium Theory. Oxford: Clarendon Press. ISBN 978-0-19-851892-1.
- ^ Levy, O., & Stroud, D. (1997). Maxwell Garnett theory for mixtures of anisotropic inclusions: Application to conducting polymers. Physical Review B, 56(13), 8035.
- ^ Liu, Tong, et al. "Microporous Co@ CoO nanoparticles with superior microwave absorption properties." Nanoscale 6.4 (2014): 2447-2454.
- ^ Jepsen, Peter Uhd; Fischer, Bernd M.; Thoman, Andreas; Helm, Hanspeter; Suh, J. Y.; Lopez, René; Haglund, R. F. Jr. (2006). "Metal-insulator phase transition in a VO2 thin film observed with terahertz spectroscopy". Phys. Rev. B. 74 (20): 205103. Bibcode:2006PhRvB..74t5103J. doi:10.1103/PhysRevB.74.205103. hdl:2440/36406.
- ^ Belyaev, B. A.; Tyurnev, V. V. (2018). "Electrodynamic calculation of effective electromagnetic parameters of a dielectric medium with metallic nanoparticles of a given size". Journal of Experimental and Theoretical Physics. 127 (4): 608–619. Bibcode:2018JETP..127..608B. doi:10.1134/S1063776118100114. S2CID 125250487.
- ^ Zhukovsky, S. V.; Andryieuski, A., Takayama, O.; Shkondin, E., Malureanu, R.; Jensen, F., Lavrinenko, A. V. (2015). "Experimental demonstration of effective medium approximation breakdown in deeply subwavelength all-dielectric multilayers". Physical Review Letters. 115 (17): 177402. arXiv:1506.08078. Bibcode:2015PhRvL.115q7402Z. doi:10.1103/PhysRevLett.115.177402. PMID 26551143. S2CID 4018894.
- ^ Sukham, J.; Takayama, O., Mahmoodi, M.; Sychev, S., Bogdanov, A.; Hassan Tavassoli, S., Lavrinenko, A. V.; Malureanu R. (2019). "Investigation of effective media applicability for ultrathin multilayer structures". Nanoscale. 11 (26): 12582–12588. doi:10.1039/C9NR02471A. PMID 31231735. S2CID 195326315.
- ^ Kumar, Ankush; Vidhyadhiraja, N. S.; Kulkarni, G. U . (2017). "Current distribution in conducting nanowire networks". Journal of Applied Physics. 122 (4): 045101. Bibcode:2017JAP...122d5101K. doi:10.1063/1.4985792.
Further reading
- Lakhtakia, A., ed. (1996). Selected Papers on Linear Optical Composite Materials [Milestone Vol. 120]. Bellingham, WA, USA: SPIE Press. ISBN 978-0-8194-2152-4.
- Tuck, Choy (1999). Effective Medium Theory (1st ed.). Oxford: Oxford University Press. ISBN 978-0-19-851892-1.
- Lakhtakia (Ed.), A. (2000). Electromagnetic Fields in Unconventional Materials and Structures. New York: Wiley-Interscience. ISBN 978-0-471-36356-9.
- Weiglhofer (Ed.); Lakhtakia (Ed.), A. (2003). Introduction to Complex Mediums for Optics and Electromagnetics. Bellingham, WA, USA: SPIE Press. ISBN 978-0-8194-4947-4.
- Mackay, T. G.; Lakhtakia, A. (2010). Electromagnetic Anisotropy and Bianisotropy: A Field Guide (1st ed.). Singapore: World Scientific. ISBN 978-981-4289-61-0.